Profi Compression Sprayer - 10 litre
High quality sprayer, 10 litre tank capacity and 3 BAR working pressure with NBR seals for neutral chemical solutions.Read More
Our Profi compression sprayer has a 10-litre capacity working capacity, 3 BAR working pressure and a 2.5 meter recoil hose.
Special features of the product:
• Pressure gauge with safety valve
• Shut-off valve with filter screen
• Integrated filling funnel
• Foot ring for stability
• With protected hose coupling
• Extension wand 50 cm
• Padded carrying strap
• Spray Shield with Nozzle
• Spray Shield without Nozzle
In addition to this sprayer we have the Compression Sprayer Profi Plus - 5 litre which has a 5 litre working capacity.
- Nozzle - Brass, hollow cone 1.1mm
- Tank - Plastic
- Tank capacity - 12.5 litres
- Working capacity - 10 litres
- Spray wand - Brass 500mm with 360O rotatable nozzle
- Hose - 2.5m recoil hose
- Ergonomically formed shut off valve
- Seals NBR which is a synthetic rubber with high elasticity that makes it suitable for the production of seals and o-rings in this type if sprayer. The NBR is highly resistant to oils, greases and hydrocarbons and are long lasting and low wear.
Our Mesto Profi 3270 has a 10-litre capacity (also available with a 5-litre capacity) yellow, polyethylene tank with a 3 BAR maximum spraying pressure and a maximum flow rate of 1-litre per minute.
As with all of our Mesto sprayers, they are packaged in a brightly coloured box with plenty of good quality, informative photos and basic information. It is of a construction that is strong enough to both hold the sprayer and give some good protection to the unit.
Upon opening the box the first thing I looked for was an instruction manual and, once I got my hands on it, quite some instruction manual it is. In keeping with some of the other sprayers within the Mesto range, there are over 125 pages of instructions. Only 8 of them are in English but it is nice to get an instruction manual and this one tells you everything that you need to know from a welcome message and safety notices through technical information, assembly instructions, care & maintenance information and a faults guide. Having had a quick read, I decided it was time to have a look at the sprayer itself. Everything was nicely packed around the tank so to remove the sprayer from the box only required a gentle pull and wiggle on the handle and the tank lifted easily from the box. My first impression of the sprayer is that it looks like a robust piece of kit with nice bright colours and a big pump handle. I like the brass lance and nozzle and the 2.5-meter recoil hose. The coiled hose reduces the unused hose length to around 30cm so this is a nice space saving idea which also means that you are not going to get caught up in a long hose. I was slightly disappointed to see that the Profi didn’t have the integrated pressure gauge in the lance handle but that is saved for the 6 BAR sprayers.
After skimming through the instruction manual, the assembly didn’t look too difficult. There are only four parts to attach to the tank the shoulder strap, coiled hose, lance handle and lance. The shoulder strap is fed through the two slots in the rear of the top section with the black, plastic buckle used to hold the ends and adjust the strap length. TIP: feed the strap through the top of the first slot then up through the second slot. This way you don’t have to remove the buckle from the strap. The lance is easily threaded onto the lance handle and the hose connects to the handle and base of tank. TIP: I found the hose quite hard to push onto the lance handle so I dipped the end of the hose into hot water for a few moments and this softened it enough to make it far easier to attach.
The assembly only took a few minutes and wasn’t at all difficult. Remember that there are plenty of diagrams and instructions to help you so if something doesn’t make sense then go back to the instruction manual.
I was now ready to start spraying so I placed the tank on the floor and turned the tank handle anticlockwise and after a few turns pulled the central housing from the tank which allowed me to start filling. The design incorporates a nice wide filling area so spillages should be easy to keep to a minimum. I managed to fill the tank with no issues, replaced the housing and gently tightened it. I only needed to pump the tank handle a few times to bring it to full pressure and spraying was just as I would expect; a nice spray pattern was easily maintained. To release the pressure within the tank simply pull the small, red pressure release valve.
Draining of the tank was easy as the hose it attached at the base so, if you wish, you can simply unscrew the hose and the tank will fully drain.
Can I use this sprayer with your telescopic lances?
Yes. This sprayer can be used with either our 3.2 metre or 5.4 metre telescopic lances, as well as other lance extensions within our range. All you need to connect this sprayer to either of the long telescopic lances is either the Sprayer Connecting Hose or Flexible Connecting Hose.
Is there a benefit to having this type of hose?
The Profi sprayer has a recoil hose which is unusual for sprayers, the majority of which have a standard hose configuration. The benefit of a recoil hose is that you can have a much longer length of hose which only takes up a small amount of space and it is easy to keep tidy. This sprayer has 2.5 metres of hose which is double the length of many of the sprayers within our range. This is a huge benefit, compared to other sprayers, as it gives you flexibility when spraying.
What is the difference between the Profi and Profi Plus sprayers on your site?
To look at the sprayers you wouldn't notice too much difference apart from the colours, the main difference are the seals. The Profi has NBR seals and the Profi Plus has FPM seals. This means that the Profi Plus can handle more acid based chemicals than the Profi so if you are looking to use your sprayer for more acidic corrosive products then you are better to purchase a Profli Plus.
You may also be interested in...